Trojan TWC-27 27-Inch Tall Work Center, 2 by 6 Not Included

Cheap Trojan TWC-27 27-Inch Tall Work Center, 2 by 6 Not Included Review

This review is for TWC-35 version of this product - 35-inches instead of 27 inches. I posted this comment here also give food for thought on both buyers height models.

In preparation for building my house, I bought the work center of Troy 35 "(TWC-35) for a price of 115.00 to fly, take my Milwaukee 12" sliding compound miter saw (seen enough heavy) . Also bought an extra roll.

Many people have to consider the 27 "or 35" kit. I did a lot of reflectionon how high I wanted the saw before buying the larger size. I used a 2x6 14 'that passes through to the last 10 months. I'm 5'8 "with a 30" inseam, and I never once thought about the height of the saw with this configuration - it was perfect. The material is there, safely in front of you without bending over. My 5'7 "with 28" inseam 76 years old father has put a lot of time on this saw / stand and prefers the 35 "too high. At this stage, I could not imagine using the center 27 Work 'per case is pretty tired as it is. I ran almost all the material through the saw, including all sizes of wood, OSB, PVC, Hardiplank, fittings, etc., and never had a negative thought about the final height was seen with 35 "2x6 legs and crosses. I have 27" legs too, and it is unnecessary to use the saw stand - 35 "is the way forward.

"I use a single clamp 24" mounted vertically as a cessation of multiple cuts of the same length, very adjustable in this way.
-If your saw is heavy, as is mine, there will be some flexibility toAssembly in the form of saw head slides on the track and the scales tip toward you. This is a very slight flexion and does not bother me.
The guide-roller extra I bought is very useful to get a roll on one side and two on the other side. Much less mobile shingle around.
-Two people can move the stand / saw combo fairly easily. Sliding he set his legs as they enter the sub-floor, particularly with a heavy saw. Does not seem to cause permanent damage, but probably not good to move around.Would cutting blade on the concrete well.
-If no help is available and the stand must be moved several ways, I just remove the base of the saw and the operations change.
-The clamping plates for wood as a person. Get placed at the correct angle, use your feet to start the legs apart to tighten the wood, then lightly step on the support via their snap in the lockset. Then do the same thing for another. Takes a little practice, but in the end I can get them quickly andsafely. The teeth dig and there is no way those legs off, unless you want them. I read about someone complaining about his legs in bulk: the standard timber size that is simply not possible. I think perhaps he does not step in the cons-ways to tighten hinge and lock. They are foolproof, if properly installed.
During the phase of siding construction, the work center stayed out of cold showers and occasional. I was initally concerned about the humidity ruiningthe base, but he has resisted. We bungeed a tarp on the saw and a work center and everything was fine. The moisture would eventually cause a problem if, if left exposed. If you break this every night and throwing coins into a truck - the base of the saw must be protected from moisture during travel. Of course, it would be fairly simple to make a new base and mount the bracket on it.
-To measure up, I'm almost using the worst case with the Milwaukee 12 "SCMS. Itis a beast and runs very well on this stand, just a bit of flex as shown.
-On occasion, I used a separate 35 "rack * Trojan I c-clamed the 2x6 work center to provide additional support for long work. Clamping by c-center woodworking wood horse saw, I could mount the previously mentioned pipe clamp on the bridge part to make several cuts long as possible. I also have a stand with casters to support rapid exit of long duration.
-Experience with 2x6 woodleg length and location for best performance, reduce some flex and give more space to move through the rollers. Watch the balance. The saw need not be centered on the 2x6 and can be positioned in the center. The instructions tell you this Trojan is that you do, but common sense allows variance. With a 2x6 long enough and some thought that we have implemented support for managing both left and right feed roller without moving much. You'll need some elbow room on site to dothis.

* I have enough extra legs of Troy for the construction of two 35 "saw horses with 2x6 timber and two 27" 2x8 wooden trestles. You can use the wood for various different heights - at your fingertips. Each level had its own uses and I am more than satisfied with the performance. Simple, very strong and very reliable. These things take a stack of weight and have not met their match at the moment - and doubt they will.

Full line of Trojan workcenters easel legs / are strong,versatile, highly mobile, and The Cat's Meow far as I'm concerned. Excellent buy, expecially if you catch the work center for sale 115-120. I never noticed the easel legs move to a sale price, but the center 35 of work "certainly did.

Trojan TWC-27 27-Inch Tall Work Center, 2 by 6 Not Included Feature

• Fast setup
• Stores conveniently
• Use with mitre saws, planers, tablesaws, drill presses
• Use any 2x lumber for the size you want- 27 inch to top of 2 x 4
• Gripping teeth clamp wood without screws of nails

Trojan TWC-27 27-Inch Tall Work Center, 2 by 6 Not Included Overview

The Trojan Work Center is so easy to set up, in just seconds you've got a work station that keeps you and your work off the ground. Ball bearing rollers adjust to the proper height and make material feed easily. The rollers stow conveniently with the table to make a briefcase size unit to carry between jobs. The work center is suitable for use with miter saws, planers, table saws, drill presses, radial saws, extra horses, etc. Trojan TWC27 Includes: Sawhorse legs, 2 roller brackets, saw table. Use any 2x lumber to adjust height and length. Saw horse legs self level so Workcenter is sturdy even on uneven terrain. Additional rollers available (model TR-10). Saw NOT Included.



*** Product Information and Prices Stored: May 02, 2010 11:02:35